Tamko Driveway & Pavers Nationwide

Tamko Driveway & Pavers: The Campbell Owner’s Guide

We stock and install Tamko-compatible driveway and paver systems in Campbell, with paver driveway installations running $7,000-$18,000 and concrete driveway work at $4,500-$12,000 depending on substrate condition and square footage. Most Tamko paver pattern failures we see in Campbell trace back to base settlement after winter rains or edge restraint breakdown where the polymer sand has washed out. The symptom picture is usually gradual: a paver that rocks underfoot, then a visible dip forming near the garage apron or downspout outlet, then water pooling where it used to drain.

Call (831) 704-1211

Which Tamko Models This Applies To

Tamko’s paver line centers on the Heritage Series and the commercial-grade ProLine, both distributed through select dealers in Santa Clara County. Heritage uses a 60mm thickness with beveled edges; ProLine steps to 80mm with a chamfered profile designed for vehicular load. The part you’re actually replacing in most cases isn’t the paver itself but the edge restraint, bedding sand, or the geotextile fabric beneath the base course. Check the paver edge for a stamped “TAMKO” and a two-digit year code. The compatibility gotcha in Campbell: Heritage pavers from pre-2018 lots used a slightly different chamfer angle that doesn’t lock cleanly with current edge restraint profiles. If your driveway was installed before 2018, bring a spare paver or a clear photo of the edge profile. We carry both OEM Tamko edge restraints and the Keystone-compatible aftermarket equivalent, which matches spec at roughly 15% less cost but carries a shorter warranty. Rowan Construction Group Campbell is an independent service provider, not affiliated with Tamko.

Signs Your Tamko Driveway & Pavers Is Failing

• Pavers rock or shift underfoot. This usually means the bedding sand layer has eroded or compacted unevenly, often where roof runoff concentrates. In Campbell, we see this most on north-facing driveways where moss retains moisture and accelerates sand migration.
• Visible dips or low spots forming. The base course, typically 3/4-inch crushed aggregate, has settled or washed out. This happens where the geotextile fabric tore during original installation or where tree roots from adjacent properties have pushed upward.
• Polymer sand cracking and weeds growing through joints. The joint stabilizer has degraded from UV exposure and thermal cycling. Campbell’s 90°F summer peaks to near-freezing winter lows stress the binder faster than milder coastal climates.
• Edge pavers tilting outward or separating from the field. The edge restraint, usually a vinyl or aluminum spike-in strip, has pulled loose. This is the first failure mode we check on every Tamko paver call in Campbell.
• Water pooling where drainage used to work. The original pitch, typically 1/8 inch per foot, has been lost to base settlement. In the Pruneyard area and other Campbell neighborhoods with clay-heavy soil, this can happen within 5-7 years if the base wasn’t fully compacted in lifts.

Before

After

Replacement Cost & What’s Included

For a Tamko paver driveway replacement in Campbell, expect $7,000-$18,000 installed. The range driver is square footage and what’s beneath the pavers: if the base course is salvageable, you’re at the lower end; if we need to excavate and recompact 6-8 inches of base plus install new drainage, you’re toward the upper. Concrete driveway replacement runs $5,000-$14,000. Driveway sealing, which extends paver life and restores color saturation, is $250-$700. Every quote we write breaks out parts, labor, base preparation, and disposal as separate line items. Under Clause 1 of the Haven Standard, that written price is fixed; no change proceeds without a signed change order. The 365-Day Done Right Promise covers the installation, and we pull all required Campbell permits and pass inspection before final payment.

DIY or Call Us?

An owner can safely check for loose edge restraints or measure a paver dip with a 4-foot level. What goes wrong fast: lifting settled pavers without understanding why they settled. The base beneath is compacted aggregate, not dirt, and simply adding sand underneath creates a soft spot that fails again in months. For polymer sand reapplication, the joints must be completely dry and the sand fully swept and compacted before water activation; partial jobs look worse than the original failure. We don’t recommend DIY base excavation. The tools to compact 6-inch lifts properly weigh 200 pounds and require experience reading substrate moisture content. If you’re seeing base settlement, call (831) 704-1211. We’ll photograph the failure, explain what’s actually happening beneath the surface, and give you a written price before any work starts.

FAQs

How long do Tamko pavers last in Campbell’s climate?

With proper base preparation and periodic sealing, 25-30 years. Without sealing, the polymer sand fails in 5-7 years and edge restraints in 8-10, which accelerates pafer degradation. Call (831) 704-1211 for an exact quote on your specific installation - estimates are free.

Can the pavers be repaired instead of replaced?

Partial repair works if the base is sound and the failure is isolated to edge restraints or joint sand. Once base settlement exceeds 3/4 inch or affects more than 15% of the surface, spot fixes create visible elevation changes that trap water. We assess this on every call and document it with photos. Call (831) 704-1211 for an exact quote - estimates are free.

How long does a full replacement take?

Most Tamko paver driveway replacements in Campbell run 3-5 business days: one day for excavation and base prep, one for compaction and grading, one for paver laying, plus cure time for edge restraint adhesive. Weather and permit inspection scheduling can add a day. Call (831) 704-1211 for an exact quote with timeline - estimates are free.

Do you stock Tamko parts?

We stock edge restraints, polymer sands, and geotextile fabric compatible with Tamko profiles. Specific paver colors and textures we source from Tamko’s San Jose-area distributor with 2-3 day lead time. We also stock KraftMaid cabinet hardware, Cambria and Silestone seam kits, and a range of other brand-specific parts across our trades. Call (831) 704-1211 to confirm availability for your color match - estimates are free.

Written by Grant Rowan, Owner, Rowan Construction Group Campbell at Rowan Construction Group Campbell, serving Campbell and nearby areas.